-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueOpportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
Manufacturing Know-how
For this issue, we asked our expert contributors to share their thoughts on the absolute “must-know” aspects of fab, assembly and test that all designers should understand. In the end, we’re all in this together.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Kelly Dack and Mark Thompson Unite in the War on Failure
September 9, 2015 | Andy Shaughnessy, PCBDesign007Estimated reading time: 2 minutes
There’s been a lot of talk about fighting the war on failure in the PCB industry. But what strategies should our generals follow to prosecute this war? What exactly constitutes a failure in the first place? Is this war even winnable? I recently spoke with longtime designer Kelly Dack and CAM support veteran Mark Thompson of Prototron Circuits about the best battle plans for beating failure, and why designers and manufacturers must team up against this common enemy.
Andy Shaughnessy: Kelly, you recently said, "Failure wins when it leverages the guerrilla warfare tactic of divide and conquer to confuse and disorient the product development community. Designers and manufacturers must unite to fight this war.”
Why don't you start off by saying what failure means to each of you at the design stage and at the board shop stage?
Kelly Dack: Andy, failure is defined as not meeting the intended objective. But I think the concept is easily confused if coming from isolated design and manufacturing perspectives. Meeting the intended objective successfully can only come from allied efforts. Designers need to describe or define objectives for their projects in terms of concise orders in order to make successful products, but this will only come about if the folks giving orders are also able to follow orders.
Mark Thompson: Absolutely, I agree with Kelly entirely. I'd say from the fabrication side, following orders is easy if the orders are given from time-proven, industry standard specification. We open the door for failure when we have to question orders. But we manufacturers have to occasionally, when the orders are outside of the guidelines of conventional process or machine capability. Designer and manufacturer communication and respect is key here, and I think this is why Kelly mentions that it is important that those giving orders must be willing to take them if the order would put the part at risk of failure.
Shaughnessy: Is failure always someone's fault or is it the fault of a bad process, or is it a combination of both?
Dack: I’m not comfortable pointing fingers at individuals. The causes for success and failure can be attributed to people, but it can also be caused by unforeseen conditions or even acts of God. A good strategy is to identify performance requirements and operating conditions. The “battle plan” needs to identify constraints: design constraints, manufacturing constraints, performance constraints, even cost constraints. Knowing the enemy and anticipating every possible way a design could possibly fail is crucial, but it can’t happen in a vacuum. It must occur through open communication with the allies – stakeholders of the product who are connected through the process steps.
Thompson: If you're asking if every failure is someone's fault, I would say yes, at the most base level. It will always turn out to be someone's fault either due to negligence or lack of vigilance. But, as Kelly said, there are extenuating circumstances. There can be dynamic situations where environmental, human or mechanical conditions create a failure in the field. Or it could be a poor design type of situation, where something wasn't properly considered in the original design phase. It’s a good time to draw in the metaphor of a combat unit here. No one person in a combat unit takes credit for the unit’s success or failure. They are a team!
To read this entire article, which appeared in the August 2015 issue of The PCB Design Magazine, click here.
Suggested Items
PCBflow Helps Designers Choose Best Manufacturer for the Job
03/28/2024 | Andy Shaughnessy, Design007 MagazineI recently spoke with a few technologists who have first-hand experience with PCBflow: Susan Kayesar, technical product manager with Siemens; Evgeny Makhline, CTO of Nistec, a CEM based in Israel; and Peter Tranitz, senior director of technology solutions and leader of the IPC Design Initiative. They explain how PCBflow functions, from the designer’s and manufacturer’s viewpoint, and how this database helps break down the wall between these stakeholders.
Elementary, Mr. Watson: Ensuring Design Integrity
03/28/2024 | John Watson -- Column: Elementary, Mr. WatsonBack in February, many of us watched the "Big Game." It reminded me of the saying, “It's not how you start that is important, but rather how you finish." It is perfectly okay when you are talking about sports, you get off to a bad first half and need to recover in the second half. However, when it comes to PCB design, this is not a good practice. If things start badly, they usually don't recover. They continue down that same path, costing more money and losing design time.
Arrow Electronics Launches Intelligent Vision Ecosystem
03/27/2024 | BUSINESS WIREArrow Electronics, Inc. is utilizing the onsemi Imager Access System (IAS) module standard for developing intelligent vision solutions for use in robotics, machine vision, commercial cameras and other uses.
Dymax Will Exhibit Light-Cure Solutions for Today’s Electronics at IPC APEX 2024
03/26/2024 | DymaxDymax, a leading manufacturer of rapid and light-curing materials and equipment, will exhibit at the IPC APEX EXPO 2024 in Anaheim, CA, April 9-11.
Synopsys Announces New AI-Driven EDA, IP and Systems Design Solutions At SNUG Silicon Valley
03/25/2024 | PRNewswireSynopsys, Inc. kicked off its annual flagship Synopsys User Group (SNUG) conference in Silicon Valley at the Santa Clara Convention Center with a keynote presentation by Synopsys president and CEO Sassine Ghazi. Ghazi discussed the unprecedented innovation opportunities and challenges that technology R&D teams face in this era of pervasive intelligence.